How to Take Apart an Xbox One Controller? Step by Step Guidelines

This post has affiliate links. At no cost to you, When you buy through links on our site, As an Amazon Associate I earn from qualifying purchases.

Have you succumbed to the feared Red Ring of Death? Would you like to make Microsoft extremely frantic?

Then, make your Xbox one controller more amazing through the enchantment of modding.

If you have tolerance and courage enough to void your guarantee, read the guidelines.

Read through the article and you’ll figure out how to take apart an Xbox one controller.

Step 1: Take aside the faceplate

Flip around the Xbox one controller. Then, put your finger in the gap and draw forward. A decent pull will be essential.

Step 2: Evacuate the lower flame broil

There are six tabs in an Xbox one controller. The tabs have taken cover behind the venting gaps on the white side that hold this piece on. Utilizing your case opening device or little screwdriver, pop all the tabs each one in turn. Then, gradually evacuate the lower frame broil. Begin at the front end. The faceplate situates at the front end of the device.

Step 3: Expel the upper grill

In the first place, pull off the hard drive in the event that you haven’t as of now. You will see that the flame broil on this side isn’t level. You should pop the two tabs which situate along the edge first. At that point pop the two tabs which are obvious on the sides, much like the lower flame broil. One of the elastic feet covers up the last tab. This tab has a seal, which will demonstrate to Microsoft that you have broken your warranty. This will have a decent place to get a handle on the flame broil to lift it as you go.

Step 4: Open the two gap tab area

These two tabs, situated alongside the power plug. They will most likely be flown in the meantime. This is the point at which you will need to exploit the second little screwdriver. Utilizing both of the screwdrivers or the case opening instrument, open the tabs. Lastly, begin to pry the shell open.

Step 5: Open the five gap tab segment

At the opposite end of that side, you will see five a greater amount of these tabs. Pop them each one in turn. Try to keep a steady weight when you’re opening the shell. Besides, you can utilize the case instrument to open them at the same time.

Step 6: Open the shell

Flip the Xbox one controller around to take a gander at the front end. Discover the clasp toward the end close to the DVD drive. You can open this with your fingernail and a decent arrangement of prying. Also, using a flathead screwdriver you can open the shell. There ought to be four tabs on this side, which you can take each one in turn.

Step 7: Unscrew the inward packagin

With the shell evacuated, you ought to have the capacity to see the internal packaging now. Unscrew the cover board and open this. Then, turn the Xbox onto the other side and draw off the rest of the shell to uncover the inward segments.

Step 8: Tenderly expel the DVD drive

The links which are appended to the DVD drive are extremely sensitive. So, expel this segment first with care.  Then, lift it up sufficiently only to get to the links and after that tenderly haul out them two.

You can flash the DVD drive through a complex modding process. Modding is necessary if certain breakdowns happen. If Microsoft finds this kind of modding, it will get you a lifetime restriction from Xbox Live.

Step 9: Fly out the fan

In the first place, lift the white area of plastic. The fan underneath can be flown out, yet there are additional links connected. So precisely expel those before hauling the fan out the greater part of the way.

Step 10: Evacuate the ring light

The ring controls are effortlessly gotten to for modding or repair once the case is open this way.

Step 11: Access the motherboard

The motherboard will likewise now be effortlessly obvious and open. You can deliberately pull it up by the silver box at the middle or fix it set up. Evacuating the motherboard can enable you to settle the heatsink by re-welding. It will likewise permit you access for programming or firmware mods. Simply recollect that these are exceptionally mind-boggling forms. Also, Evacuating the motherboard illegally can get you prohibited by Microsoft.

Step 12: Mod the hard disk drive

In spite of the fact that it isn’t situated in the fundamental case, you can likewise open the hard plate drive. And introduce a drive with more storage room. Lastly, finish the modding by unscrewing the majority of the pieces, and sliding it out of the sound. Now it is supplanted with another hard drive, as the links utilized are standard.

Another Article on Xbox one games

Final Words

Xbox One controller is an excellent gaming device. Also, you can make it more excellent by yourself by adding by the magic of modding. Again, to paint it or clean it, you may need to take apart the part of this device. Here, I’ve discussed the steps on how to take apart an Xbox one controller. Read it thoroughly and you will be able to easily disassemble your Xbox one controller. Enjoy your game.

Categories How To

1 thought on “How to Take Apart an Xbox One Controller? Step by Step Guidelines”

  1. When I originally commented I clicked the “Notify me when new comments are added” checkbox and
    now each time a comment is added I get four e-mails
    with the same comment. Is there any way you can remove me from that
    service? Thank you!


Leave a Comment